Precaution, Pretection and Safety, all in FireTC
firetc@firetc.com
 
Inquiry For Fire Testing
 
Recommended Service
Hot Fire test center
 
Your location: Home » Fire test center » Standards & Regulation » USA » Text

ASTM C1086 Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation

Zoom  Zoom Issue Date:2012-02-13   Browse:1382
ASTM C1086玻璃纤维油毛毡热绝缘标准规范
ASTM C1086 Standard Specification for Glass Fiber Mechanically Bonded Felt Thermal Insulation
ASTM C1086玻璃纤维油毛毡热绝缘标准规范
This specification covers glass fiber unsupported needled felt binder-free thermal insulations. This material is used as the thermal insulation component in the fabrication of insulation systems for use on machinery and equipment, such as steam turbines, boilers, boiler feed pumps, and piping at specified elevated temperatures. Thermal insulations should adhere to the following physical requirements: apparent thermal conductivity, hot surface performance, tensile strength, non-combustibility, and dimensions (nominal thickness, mass per unit area, length, and width).
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers glass fiber unsupported needled felt (mechanically bonded) binder-free insulation for thermal insulation. This material is used as the thermal insulation component in the fabrication of insulation systems for use on machinery and equipment, such as steam turbines, boilers, boiler feed pumps, and piping at temperatures from ambient up to 1200°F (650°C).
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 See Supplementary Requirements for modifications to paragraphs in this standard when using Specification C 1086 in lieu of the United States Department of Defense, Department of Navy, Naval Sea Systems Command, in Washington, DC. Military Specifications No.(s) MIL-I-16411F.

2. Referenced Documents (purchase separately)
ASTM Standards
C167 Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C1045 Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C1058 Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
D123 Terminology Relating to Textiles
D578 Specification for Glass Fiber Strands
U.S. Federal Standard
FED-STD-191 Textile Test Methods
U.S. Military Standards
MIL-STD-1623 Fire Performance Requirements and Approved Specifications for Interior Finish Materials and Furnishings (Naval Shipboard Use)
Index Terms
binder free; glass fiber felt; glass fiber; needled felt
; Acidity, alkalinity, pH; Boiling water resistance; Bonded and laminated apparel fabrics--specifications; Defects; Degradation--thermal insulation; Exposure tests; Felt thermal insulation--specifications; Fibers; Fusion; Glass thermal insulation--specifications; Insulation--specifications; Quality conformance (federal); Quality control (QC)--insulation (thermal); Temperature tests--thermal insulation; Tensile properties/testing; Thermal insulating materials--specifications ;
 
 
[ Fire test center Search ]  [ ]  [ Forword to friends ]  [ Print ]  [ Close ]  [ Back to Top ]

 

 
 
Home | About us | Contact | Terms & Conditions | Copyright | Site Map | Friend link | Guestbook | Old Version | 闽ICP备09009213号
©2013-2015 FIRETC.NET All Rights Reserved   ICP:闽ICP备09009213号-4