Precaution, Pretection and Safety, all in FireTC
Inquiry For Fire Testing
Recommended Service
Hot Fire test center
Your location: Home » Fire test center » Standards & Regulation » USA » Text

ASTM D3806 Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method)

Zoom  Zoom Issue Date:2012-02-10   Browse:1878
ASTM D3806小规模评价阻燃涂料标准试验方法(2英尺通道法)
ASTM D3806 Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method)
ASTM D3806小规模评价阻燃涂料标准试验方法(2英尺通道法)
A number of laboratory procedures are used to evaluate the effectiveness of fire-retardant and fire-resistant treatments and coatings. In general, these methods measure the three stages of fire development: (1) ignition; (2) flame spread (rate of growth of the fire); and (3) conflagration extent. While all three are of extreme importance, flame spread has been recognized as the main factor associated with testing fire-retardant coatings.
Flame spread ratings based upon Test Method E84 have acquired common acceptance by regulatory agencies, but such large-scale tests are seldom practical during the development or modification of a fire-retardant coating.
This test method provides the relative flame spread of experimental coatings using small test specimens. By calibrating the 2-foot tunnel with Test Method E84-rated fire-retardant paint, results obtained by this test method should be indicative of those obtained with a large specimen in the Test Method E84 tunnel.
1. Scope
1.1 This test method determines the protection a coating affords its substrate, and the comparative burning characteristics of coatings by evaluating the flame spread over the surface when ignited under controlled conditions in a small tunnel. This establishes a basis for comparing surface-burning characteristics of different coatings without specific consideration of all the end-use parameters that might affect surface-burning characteristics under actual fire conditions.
1.2 In addition to the experimental flamespread rate, the weight of panel consumed, time of afterflaming and afterglow, char dimensions and index, and height of intumescence may be measured in this test. However, a relationship should not be presumed among these measurements.
1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions, and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately)
Federal Standard
Fed.Spec.TT-V-119 Varnish, Spar, Phenolic Resin
ASTM Standards
C220 Specification for Flat Asbestos-Cement Sheets
D344 Test Method for Relative Hiding Power of Paints by the Visual Evaluation of Brushouts
D1475 Test Method For Density of Liquid Coatings, Inks, and Related Products
D2196 Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer
E84 Test Method for Surface Burning Characteristics of Building Materials
Index Terms
fire-retardant; flame spread; paints; tunnel method; Burning characteristics--paints/related coatings/materials; Fire testing--paints/related coatings/materials; Flame spread; Flammability--paints/related coatings/materials; Paint testing; Tunnel method; Two-foot tunnel method
[ Fire test center Search ]  [ ]  [ Forword to friends ]  [ Print ]  [ Close ]  [ Back to Top ]


Home | About us | Contact | Terms & Conditions | Copyright | Site Map | Friend link | Guestbook | Old Version | 闽ICP备09009213号
©2013-2015 FIRETC.NET All Rights Reserved   ICP:闽ICP备09009213号-4