Precaution, Pretection and Safety, all in FireTC
firetc@firetc.com
 
Inquiry For Fire Testing
 
Recommended Service
Hot Fire test center
 
Your location: Home » Fire test center » Standards & Regulation » USA » Text

ASTM F1742 Standard Specification for PVC Insulating Sheeting

Zoom  Zoom Issue Date:2012-02-08   Browse:1169
ASTM F1742 PVC绝缘薄板标准规范
ASTM F1742 Standard Specification for PVC Insulating Sheeting
ASTM F1742 PVC绝缘薄板标准规范

This guide provides a recommended list of selected ship structure details for use in ship construction. Structural details which have failed in service and are not recommended for use in ship construction are included as well. This guide is intended to convey the lessons learned on different configurations of ship structure details, not the dimensions, thickness, or construction methods which would result from structural calculations. Details are shown for the ten families of structural details, which are: beam brackets, clearance cut-outs, gunwale connections, miscellaneous cut-outs, non-tight collars, panel stiffeners, stanchion ends, stiffener ends, tight collars, and tripping brackets. Evaluation of details is based on in-service experience as described in "Design Guide for Structural Details". Data for over 400 details is summarized and rated by observed relative successful performance. Each of the ten families of details includes configurations with no signs of failures. The details without failures within each family group are shown in descending order of numbers observed. Those details with failures are shown in ascending order of failures (percentages are indicated for each). Thus the first detail shown in each family group has the best observed service performance and is most highly recommended while the last has the highest failure rate and therefore least desirable. The details provide guidance in the selection of structural detail configurations in future design and repair of such details.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers acceptance testing of Poly Vinyl Chloride insulating sheeting for use as a covering for protection of workers.
1.2 The following safety hazards caveat applies only to the test method portion, Sections 17-19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 18.1 for a specific warning statement.

2. Referenced Documents (purchase separately)
American National Standard
ANSIC84.1 Voltage Ratings for Electric Power Systems and Equipment (60 Hz)
ASTM Standards
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension
D570 Test Method for Water Absorption of Plastics
D747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam
D1004 Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
D1048 Specification for Rubber Insulating Blankets
D1746 Test Method for Transparency of Plastic Sheeting
D2240 Test Method for Rubber Property--Durometer Hardness
Index Terms
Plastic sheet and film--specifications; Poly(vinyl chloride)(PVC) sheet/film--specifications; Protective equipment--specifications;
 
 
 
[ Fire test center Search ]  [ ]  [ Forword to friends ]  [ Print ]  [ Close ]  [ Back to Top ]

 

 
 
Home | About us | Contact | Terms & Conditions | Copyright | Site Map | Friend link | Guestbook | Old Version | 闽ICP备09009213号
©2013-2015 FIRETC.NET All Rights Reserved   ICP:闽ICP备09009213号-4