Precaution, Pretection and Safety, all in FireTC
firetc@firetc.com
 
Inquiry For Fire Testing
 
Recommended Service
Hot Fire test center
 
Your location: Home » Fire test center » Standards & Regulation » USA » Text

ASTM D902 Standard Test Methods for Flexible Resin-Coated Glass Fabrics and Glass Fabric Tapes Used for Electrical Insulation

Zoom  Zoom Issue Date:2012-02-08   Browse:1593
ASTM D902电绝缘用柔性涂树脂玻璃布和玻璃纤维绝缘带标准试验方法
ASTM D902 Standard Test Methods for Flexible Resin-Coated Glass Fabrics and Glass Fabric Tapes Used for Electrical Insulation
ASTM D902电绝缘用柔性涂树脂玻璃布和玻璃纤维绝缘带标准试验方法

The electrical properties of resin-coated glass fabrics are affected by their temperature and moisture content. For this reason it is necessary to control these properties for a specified time immediately prior to testing in order to attain reasonably good reproducibility of test values. The time of exposure to the conditioning atmosphere must be long enough to permit the test specimen to reach a relatively stable value. Usually the moisture content of these materials has little effect on the mechanical properties.
1. Scope
1.1 These test methods cover procedures for the testing of resin-coated glass fabrics and glass fabric tapes (Note 1) to be used as electrical insulation.
Note 1 - Methods of testing varnished cloths and tapes are given in Methods D 295.
1.2 The warp threads in fabrics are the threads that are parallel with the length dimension as manufactured.
1.3 The procedures appear as follows:
1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statement are given in 35.1.1 and 58.1.
2. Referenced Documents (purchase separately
ASTM Standards
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D295 Test Methods for Varnished Cotton Fabrics Used for Electrical Insulation
D374 Test Methods for Thickness of Solid Electrical Insulation
D828 Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
D1711 Terminology Relating to Electrical Insulation
D1830 Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method
D3487 Specification for Mineral Insulating Oil Used in Electrical Apparatus
D5032 Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
D5423 Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
E104 Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions
IEEE Standard
IEEENo.1 General Principles for Temperature Limits in the Rating of Electrical Equipment
Index Terms
breaking strength; coated glass fabric; dielectric breakdown voltage; dissipation factor; heat aging; permittivity; thermal endurance; thread count;
 
 
 
[ Fire test center Search ]  [ ]  [ Forword to friends ]  [ Print ]  [ Close ]  [ Back to Top ]

 

 
 
Home | About us | Contact | Terms & Conditions | Copyright | Site Map | Friend link | Guestbook | Old Version | 闽ICP备09009213号
©2013-2015 FIRETC.NET All Rights Reserved   ICP:闽ICP备09009213号-4